|
Minelab 12V Car Charger
The 12 V car charger is suitable for Explorer II, Musketeer Advantage, Sovereign Elite and Eureka Gold detectors. Charge your detector battery from the cigarette plug in your car, any time you are away from mains power.
See Details
|
|
Minelab 110V Charger
The 110V wall charger is suitable for Explorer II, Musketeer Advantage, Sovereign Elite and Eureka Gold detectors.
|
|
12V Charger for GPX-4000
This is the 12V charger for the Minelab GPX-4000 Lithium Ion battery. It will not work with any other models.
|
|
Small Battery SD/GP 4.5A 6V
This half-size battery for the Minelab SD and GP series detectors (except the SD2000) does not last as long as the stock battery but does weigh less at about 2 pounds. Nice for those that normally only detect a few hours at a time. This is not an aftermarket item but is a genuine Minelab accessory.
|
|
AA Battery Holder (4 AA)
This battery pack holds four AA batteries. Two of them are used in the Minelab Sovereign XS, XT 17000, and Ameican Gold Striker models.
|
|
Eureka AA Battery Pack
This is a replacement snap-in AA battery holder for the Minelab Eureka Gold. It is a nice way to carry spare batteries in the field. Just snap out one set when they get low, and snap in the replacement set. Batteries not included. Blue color matches Eureka Gold.
See Details
|
|
Large Battery SD/GP 12A 6V
This is a genuine Minelab replacement battery for the battery that comes stock with the Minealb SD and GP series detectors, except the SD2000. Make sure you always have a spare battery ready to go! If you want to charge your spare battery while using your detector, be sure and get a spare power cord also.
See Details
|
|
|
|
10" Elliptical Scuff Cover
This is the replacement scuff cover for the Minelab XT18000 and Minelab Eureka Gold standard elliptical searchcoil.
|
|
11" Round Scuff Cover
Replacement white plastic scuff cover for the one provided as stock for the 11" round mono or 11" round DD Minelab coils for the SD/GP series detectors. Also for 11" round Goldsearch coil for the XT series and Eureka Gold.
|
|
Scuff Cover for Explorer II
This ia a replacement scuff cover for the one that comes standard one the Minelab Explorer XS and Explorer II.
|
|
|
|
9" Round Scuff Cover X-Terra
This is the replacement round 9" scuff cover for the one that comes standard with the X-Terra 30, 50, and 70 models.
|
|
|
|
9" Coil 3 kHz for X-Terra 70
This optional 3 kHz high frequency 9" round concentric searchcoil will only work on the Minelab X-Terra 70 models. It will not work on the X-Terra 30 or X-Terra 50. The low 3 kHz frequency is ideal for enhancing the signal on silver coins and improving iron discrimination. Includes scuff cover.
|
|
9" Coil 18.75 kHz XTerra 50/70
This optional 18.75 kHz high frequency 9" round concentric searchcoil will only work on the Minelab X-Terra 50 and Minelab X-Terra 70 models. It will not work on the X-Terra 30. The higher frequency is ideal for enhancing signals from gold jewelry and gold nuggets. Includes scuff cover.
|
|
10"x 5" DD Coil X-Terra 50/70
This elliptical 10" x 5" DD coil changes the Minelab X-Terra 50 and X-Terra 70 models to the 18.75 kHz higher frequency mode of operation. A DD coil has a narrowed search field that can better pick between trasy items and yet the 10" elliptical design covers a tad more ground than the stock X-Terra coil. The coil also excels in diificult ground conditions and is the perfect companion for the X-Terra 70 Prospect Mode. This coil will not work on the X-Terra 30. Includes scuff cover.
|
|
10.5" Round DD 7.5 kHz Coil
This round 10.5" DD coil for the Minelab X-Terra models runs at the satandard 7.5 kHz higher frequency mode of operation. Coin hunters looking for extra depth will find it a worthwhile addition. This coil works on all X-Terra models including the X-Terra 30. Scuff cover included.
|
|
10.5" Round DD Coil XT 50/70
This round 10.5" DD coil changes the Minelab X-Terra 50 and X-Terra 70 models to the 18.75 kHz higher frequency mode of operation. This coil will cover more ground and get more depth in difficult ground than the stock X-Terra coil. It is the perfect companion for the X-Terra 70 Beach mode and prospectors looking for extra depth will also find it a worthwhile addition. This coil will not work on the X-Terra 30. Scuff cover included.
|
|
6" Coil 7.5 kHz for X-Terra
This optional 7.5 kHz high frequency 9" round concentric searchcoil will work on all the Minelab X-Terra models. The small size is great for working in trashy areas and tight areas.
|
|
6" Coil 18.75 kHz XTerra 50/70
This optional 18.75 kHz high frequency 6" round DD searchcoil will only work on the Minelab X-Terra 50 and Minelab X-Terra 70 models. It will not work on the X-Terra 30. The higher frequency is ideal for enhancing signals from gold jewelry and gold nuggets. The DD design handles mineralized soil better than a concentric coil and provides better target separation.
|
|
|
|
Eureka Gold Hipmount Bag
This genuine Minelab bag with strap allows you to hip or chest mount the Minelab Eureka Gold. Also works with Minelab Sovereign GT control box.
See Details
|
|
Minelab Deluxe Carry Bag
This newly redesigned carry bag is suitable for all of Minelab's detectors. This tough padded bag is ideal for storing and transporting your Minelab detector. Extra width at the front of the bag will allow it to fit up to an 18" coil.
|
|
|
|
Minelab Extended Service Plan
The Genuine Minelab ESP (Extended Service Plan) provides two years of additional Extended Warranty. This gives you four years of warranty coverage on most Minelab models (two years for the Excalibur).
|
|
Rubber Teardrop Washer
This is the teardrop shaped rubber washer used to provide friction at the searchcoil on many Minelab models, including the SD/GP series units, Eureka Gold, Musketeers, Sovereigns, Excaliburs, and more. Normally two used per unit.
|
|
|
|
Black Nylon Bolt & Wingnut 2"
This is the longer of the two wingnut sizes used on the Minelab SD/GP detectors to hold various things together, this one being 2" long, the other being 1.5" long. So this is the best one to carry as a spare as it will work to replace any nylon bolt and wingnut on the SD/GP series. Everyone should have a few of these!
|
|
|
|
|
|
Curly Power Cable for SD/GP
This is a genuine Minelab replacement power cable for the one that comes stock on the Minelab SD/GP series detectors, except the SD2000. This cable is a longer lasting heavier duty power cable than that provided with the SD units. You need one of these as the power cable can fail with heavy use and if it does... you are out of business! Also required if you have a spare battery and want to charge it while using your detector.
See Details
|
|
Heavy Duty 2" Bolt & Wing Nut
This heavy duty nylon bolt and wing hut is slightly thicker than the bolt used on most Minelab detectors. It is used on the 8" coil for the Explorer II and Quattro MP. This is also the same bolt as used on the Coiltek UFO and Mini-UFO coils, except that it is black.
|
|
Commander 8" Round Mono Coil
This round Commander 8" mono coil for the Minelab SD/GP series nugget detectors is great for working in tight locations. It is inherently more sensitive to small gold than larger coils and so is great for sniping bedrock. Be aware that the enhanced sensitivity can also make this coil more prone to signals from hot rocks that larger coils would ignore. Scuff cover included.
|
|
18" Round Mono Commander Coil
The 18" Round Monoloop offers superb depth and high sensitivity in low to medium mineralization. This coil will find targets in heavily worked areas where other operators have given up. For Minelab SD2100, SD2200D, GP Extreme, GP 3000, and GP 3500 metal detectors. Includes scuff cover.
|
|
15"x12" DD Commander Coil
This 15" x 12" Semi-Elliptical Double D searchcoil provides greater depth and more ground coverage than the 11" DD. It provides stable operation in all soils. This is a great coil for all-round use in highly variable soils and a lighter, more maneuverable alternative to the 18" DD when seeking out large nuggets in heavy mineralization. Its semi-elliptical design provides impressive sensitivity for its size. For Minelab SD2100, SD2200D, GP Extreme, GP 3000, and GP 3500 metal detectors. Includes scuff cover.
|
|
18" Round DD Commander Coil
The 18" round Double D is a serious coil for the serious operator! The 18" DD punches deep through heavy mineralization, while running smooth to allow you to hear those mellow, deep nugget responses. For Minelab SD2100, SD2200D, GP Extreme, GP 3000, and GP 3500 metal detectors. Includes scuff cover.
|
|
15"x12" Mono Commander Coil
The 15" x 12" Semi-Elliptical Monoloop coil has better depth on larger nuggets than the 11" Monoloop and the 15" x 12" DD, and it is very sensitive for its size. It is great for searching open areas for new patches and when seeking out deeper nuggets in areas that are too vegetated to allow effective use of the 18" monoloop. It is an extremely stable coil which runs smooth in all but the worst soil conditions. This coil will become a favorite for many operators. For Minelab SD2100, SD2200D, GP Extreme, GP 3000, and GP 3500 metal detectors. Includes scuff cover.
|
|
Power Lead for GPX-4000
This is the genuine Minelab power cord that comes standard with the new GPX-4000. It will not work with previous Minelab models.
|
|
Custom Koss Headphones
These headphones are supplied as standard equipment with the Minelab GP 3500 detectors. The 100 ohm Koss headphones have been custom built for the Minelab Explorer II, SD and GP series detectors. These excellent headphones give you a crisp clear signal, padded muffs that eliminate outside noise and are very comfortable to wear all day long. Supplied with a curly cord for safe flexible length. These headphones have no volume controls and so can only be used with detectors that have a volume control.
See Details
|
|
Minelab Rubbish Bag
This is the green nylon Rubbish & Finds bag that comes standard with the Minelab GP series detectors.
|
|
|
|
|
|
Handle w/Button for GPX-4000
This is a replacement handle and grip for the Minelab GP 3500 and GPX-4000 units. It includes the button in the top of the grip and cable to plug into control box, plus all hardware ready to mount on the shaft.
|
|
Lower Isolator Rod for SD/GP
This is a replacement fiberglass rod for the Minelab SD and GP series detectors. An extra rod is a must in case you experience breakage in the field. They are also popular to keep mounted on accessory coils for quick switches. Note that the ML30110027 teardrop washers and ML30110029 nylon bolt are NOT included. Order these items separately.
|
|
|
|
Instructional VHS for GP 3000
This VHS tape offers hints and tips on tuning your Minelab GP 3000. Minelab has not updated this tape since the introduction of the GP 3500 but since the units are nearly identical this tape covers most GP 3500 operations.
|
|
Instructional DVD for GP 3000
This DVD offers hints and tips on tuning your Minelab GP 3000. Minelab has not updated this tape since the introduction of the GP 3500 but since the units are nearly identical this tape covers most GP 3500 operations.
|
|
External Speaker Minelab SD/GP
This is the very popular amplifier and speaker combination from Coiltek. No batteries required; runs off detector battery. Perfect for working in areas where you want to hear what is going on around you. For SD and GP detectors except GPX-4000. The GPX-4000 requires the MLBA-DAGC adapter (below) sold separately to change from 4 pins to 5 pins.
|
|
Blue Neoprene Cover for GP
This neoprene protective control box cover for the Minelab GP series detectors will help keep your control box from getting scuffed up, while still allowing for easy control access. The exterior of the neoprene is covered with blue nylon and emblazoned with the Coiltek logo.
|
|
Heavy Duty Detector Bungee
Take the weight of your Minelab SD or GP detector off your arm! This extra heavy-duty bungee is the ideal replacement for the support bungee that comes with the Minelab SD and GP units. It instantly adjusts for proper length, even while you are still moving. You start up a ridge, and the bungee goes slack, reach down, pull the bungee out of the patented V Groove adjustment hook, tug it back into place and you have perfectly adjusted the bungee instantaneously. This bungee is much less likely to stretch and wear out than the thinner Minelab bungee. Swing those big coils all day long without fatigue! The hook/lock assembly simply hooks over the detector rod, and the quick release snap on the other end snaps onto the Minelab harness. This bungee can be easily adapted for use with other detectors, the main thing required is something on your shoulder to hook to, like a backpack strap.
See Details
|
|
DeTacc PLUS Signal Amp GPX4000
This is a beefy, reliable signal amplifier that will bring those faint signals up so loud that they will make you sit up and take notice. Made specifically for the Minelab GPX-4000 detector. Plugs into the control box, and then your power cord plugs into the amplifier. Runs off of the Minelab battery and consumes about 10 minutes of battery time in a days worth of use. Amplifies signals approximately 4 times! You will wonder how you ever lived without it. Exclusive filtering system gives clean amplified sound without annoying "hum" found in some other amplifiers. Attaches to side of detector with supplied Hook and Loop fabric. Has a volume control only for dependable no gadgets reliability.
|
|
Detector Support Harness
This is the heavy-duty bungee combined with an ingenious harness that act in tandem to take the weight of your metal detector off your arm. Do not undersetimate what long hours of swinging that detector can do to your arm. Use this support harness to completey support the weight of your detector so all you need to do is move it back and forth.
See Details
|
|
Fiberglass Handle for SD/GP
Rather than having the upper part of your detector shaft being metal, this gives you a heavy duty fiberglass shaft all the way up to your control box. The more metal you keep away from the coil of your detector the more sensitive the detector is, especially if you use large coils a lot. Comes complete with an extra long heavy duty lower rod, and works with all Minelab lower fiberglass rods.
|
|
Swing Arm Helper Handle
This swing arm gives you a second handle to hold onto when swinging your detector! Just like when using a brushcutter, this extra handle helps give you better control while sharing the weight on both arms. An absolute must for extra large coils or anyone experiencing arm strain running a detector. Clips to the detector shaft when not in use.
|
|
Short Charger Lead for SD/GP
This Coiltek 19" charger lead is great for use when charging the battery for your Minelab SD or GP model detector, allowing you to charge batteries while using the main curly power cord with your detector. It is also becoming popular for those who are attaching some of the newer small batteries directly to the SD/GP control box, eliminating the battery/harness system.
|
|
GPX-4000 Pin Adapter
Gender changer plugs to make your 4 pin SD/GP accessories, signal enhancer, amplified speaker, whatever, compatible with your new GPX-4000.
|
|
Coiltek Power Cord for GPX4000
This Coiltek heavy-duty power cord is the perfect backup cord in case your Minelab power cord fails - don't be caught short!
|
|
Li-Ion Battery System SD/GP
This Coiltek optional power system is for the Minelab SD and GP detectors. It features light weight Lithium Ion batteries and weighs only 14 ounces, making this battery system so light that many people are attaching it directly to the control box in lieu of the standard Minelab backpack mounted battery. This is great for times when you'd like to eliminate that power cord being attached to your body, like when detecting in thick brush. The system includes two (2) 7800 mAh Batteries, one (1) switchable regulator (6.7 volt for GP or 7.3 for SD series machines), an AC / DC Charger, so you can charge in your car or at home, and a Cordura Nylon Carry Pouch, to attach the battery system to your belt or detector. If you attach the battery to the control box it is recommended you purchase the Coiltek short power cord (part number MLBA-CL22) for use instead of the standard Minelab power cord. Please note that this system will not work with the new GPX-4000.
See Details
|
|
Li-Ion Battery System GPX-4000
This new Coiltek optional power system is for the Minelab GPX-4000 detector. It features light weight Lithium Ion batteries and weighs only 14 ounces, making this battery system so light that many people are attaching it directly to the control box in lieu of the standard Minelab backpack mounted battery. This is great for times when you'd like to eliminate that power cord being attached to your body, like when detecting in thick brush. The system includes two (2) 7800 mAh Batteries, one (1) regulator, an AC / DC Charger, so you can charge in your car or at home, and a Cordura Nylon Carry Pouch, to attach the battery system to your belt or detector. Also included is a short power lead for use when you want to attached the battery directly to the detector. Please note that this system will not work with any detector except the Minelab GPX-4000.
See Details
|
|
|
|
Mini-UFO 17"x10" Mono Coil
This open spoke coil is exceptionally light in weight and yet covers a full 17" of ground with every swing, and unlike standard Minelab coils for the SD/GP models it is fully waterproof! Excellent for exploring large areas. Manufactured to the highest quality standards by Coiltek, the largest supplier of aftermarket serachcoils for the Minelab SD/GP detectors. This coil includes the scuff cover and a heavy duty lower rod.
See Details
|
|
|
|
Coiltek UFO 24"x12" Mono Coil
This unique open spoke coil is light in weight and yet covers a full 24" of ground with every swing! Excellent for exploring large areas. Manufactured to the highest quality standards by Coiltek, the largest supplier of aftermarket serachcoils for the Minelab SD/GP detectors. This coil is waterproof, and includes the scuff cover and a heavy duty lower rod.
See Details
|
|
Coiltek 14" Round Mono Coil
This coil is one of the most popular aftermarket coils ever sold for the Minelab SD and GP series metal detectors. The 14" mono packs a lot of punch in a compact package and combines excellent depth on large items with good sensitivity to small items. Manufactured to the highest quality standards by Coiltek, the largest supplier of aftermarket serachcoils for the Minelab SD/GP detectors. This coil includes the scuff cover. Please note that while this coil is water resistant it is not waterproof and so should not be submerged in water.
See Details
|
|
Coiltek 15" Coil for Eureka/XT
This is the largest coil you can get for your Minelab XT17000, XT18000, or Eureka Gold. This deep seeking coil is normally used in the 6.4 kHz mode for extra depth on coin size and larger targets but if the ground mineralization allows you might get away running at higher frequencies. Besides extra depth you obviously get better ground coverage with this coil. Ideal for searching tailing piles for large gold nuggets. Scuff cover included.
See Details
|
|
|
|
|
|
Platypus Waterproof DD Coil
This Coiltek 11.5" x 8.5" DD Pro coil is totally waterproof, unlike most of the searchcoils made for the Minelab SD and GP series detectors. Perfect for those wanting to use their Minelab in and around water.
See Details
|
|
Platypus Waterproof Mono Coil
This Coiltek 11.5" x 8.5" mono Pro coil is totally waterproof, unlike most of the searchcoils made for the Minelab SD and GP series detectors. Perfect for those wanting to use their Minelab in and around water.
See Details
|
|
18.5"x12" Mono Coil for SD/GP
The new Goldstalker coils from Coiltek are a new series of extra leightweight coils. This 18.5" x 12" coil offers excellent ground coverage and depth. Includes scuff cover.
See Details
|
|
13.5"x9" Mono Coil for SD/GP
The new Goldstalker coils from Coiltek are a new series of extra leightweight coils. This 13.5" x 9" coil is narrower than the stock coil yet covers more ground. Includes scuff cover.
See Details
|
[ Home ]
[ Site Map ]
[ Contact Us! ]
[ Online Store ]
[ Policies ]
[ View Cart ]
ATVs
Boating
Diving
Mining
Miscellaneous
Snowmobiling
Prices are F.O.B. Anchorage, Alaska unless
otherwise noted. All prices and specifications are subject to change without
notice.
Copyright © 1998-2007 Alaska Mining
& Diving Supply, Inc. 3222 Commercial Drive Anchorage, AK 99501
907-277-1741 Fax 907-279-6398
webmaster
1976 - 2007 AMDS
celebrates 31 years of service!