Rubber O-Ring for P100/P180 This is the rubber oring that seals the pump housing to the back plate of the P100 through P180 series pumps. Note: older versions of these pumps used a paper gasket. 

Impeller for P180 Pump (Large)  

Honda GXH50 Engine Only This is the replacement engine for Keene and Proline 2-2.5 HP pumps. 

Honda GX120 Engine Only This is the Honda GX120 replacement engine for Keene and Proline 3HP-4HP pumps. A perfect upgrade for those that have the older, less efficient Briggs motors. Get better fuel efficiency. 

Honda GX200 Engine Only This is the Honda GX200 replacement engine for Keene and Proline 5HP-6.5HP pumps. A perfect upgrade for those that have the older, less efficient Briggs motors. Get better fuel efficiency. 

Pump Seal for 2 - 2.5HP Pumps This is the pump seal used on Keene P90 and earlier pumps used on 2HP and smaller 2-stroke engines. It does not work on the current P90 4-stroke pump. 

Pump Seal for 3 - 6.5HP Pumps This is the pump seal used on the Keene P100, P150, P160, and P180 pumps used on 3HP - 6.5HP Briggs and Honda pumps for at least the last 30 years. Also used on other popular brands of mining pumps. 

Pump Seal for 8HP-16HP Pumps This pump seal is used on most Keene P200 - P350 pumps used on 7HP - 18HP Briggs or Honda motors for at least the last 30 years. Also used on other popular brands of mining pumps. 

Keene 2.5HP 1.25" Water Pump This unit features the same Honda 2.5HP motor as the WX15, but has a higher output Keene pump attached. Keene pumps forgo the self-priming feature to give you the maximum water output possible. The 1.5" intake x 1.25" output P90 pump puts out up to 100 gallons per minute and has a maximum head of 161 feet. This unit is normally used on Keene's 2" suction dredges. Since this unit is not self-priming it should be used with the Keene FV15 footvalve (not included). Weight 19 lbs.   See Details

GX200 Honda w/2" Output Pump This unit features a Honda GX200 motor with a high output Keene P180 pump attached. Keene pumps forgo the self-priming feature to give you the maximum water output possible. The 2.5" intake x 2" output P180 pump puts out up to 300 gallons per minute and has a maximum head of 180 feet. This unit is normally used on Keene's 4" suction dredges and highbankers plus the popular twin engine 6" dredge. Since this unit is not self-priming it should be used with the Keene KEFV25 footvalve (not included). Weight 38 lbs.  See Details

GX200 Honda w/2" Pump on Base This unit features a Honda GX200 5.5 HP motor with a high output Keene P180 pump attached mounted on a steel base plate for extra stability. Keene pumps forgo the self-priming feature to give you the maximum water output possible. The 2.5" intake x 2" output P180 pump puts out up to 300 gallons per minute and has a maximum head of 180 feet. This unit is normally used on Keene's 4" suction dredges and highbankers plus the popular twin engine 6" dredge. Since this unit is not self-priming it should be used with the Keene KEFV25 footvalve (not included). Weight 40 lbs. 

Base Plate for 4 & 6.5HP  

Footvalve 1.25" Molded marlex foot valve with 1.25" inch intake, includes a plated steel strainer. 

Footvalve 1.5" Molded marlex foot valve with 1.5" inch intake, includes a plated steel strainer. 

Footvalve 2" Molded marlex foot valve with 2" inch intake, includes a plated steel strainer. 

Footvalve 2.5" Molded marlex foot valve with 2.5" inch intake, includes a plated steel strainer.